H7BX-AW NPN AC100-240
Type: H7BX-AW NPN AC100-240
Function
1 Stage Preset Counter / 2 Stage Preset Counter / Total Preset Counter / Batch Counter / Dual Counter / Tachometer
Preset stages
2stages
Rated supply voltage
100 to 240 VAC 50/60 Hz
Operating voltage range
85% to 110% of the rated power supply voltage
Power consumption
Approx. 9.6 VA
External power supply
12 VDC (±10%) 100 mA
Counter (Count range)
-99999～999999
Counter (Max. counting speed)
30 Hz/5 kHz (switching) (Minimum counting input signal width: 16.7 ms (ON/OFF ratio: 1:1)/0.1 ms (ON/OFF ratio: 1:1))
Common setting for CP1 and CP2
Counter (Input mode)
Increment decrement or increment/decrement (UP/DOWN A (command input), UP/DOWN B (individual input) and UP/DOWN C(quadrature input))
Counter (Output modes)
N / F / C / R / K-1 / P / Q / A / K-2 / D / L / H
Counter One-shot time)
0.01 to 99.99 s variable
Counter (Reset system)
External, manual and automatic reset (internal according to C, R, P and Q mode operation)
Tachometer (Pulse measurement method)
Periodic measurement
Tachometer (Sampling period)
Periodic measurement: 200 ms
Tachometer (Max. counting speed)
Periodic measurement: 30 Hz/10 kHz (selectable)
Tachometer (Count range)
0 to 999999
Tachometer (Measuring ranges)
Periodic measurement: 30 Hz: 0.01 Hz to 30.00 Hz
Periodic measurement: 10 kHz: 0.01 Hz to 10 kHz
Tachometer (Measuring accuracy)
±0.1% F.S. ±1 digit max. (at 23 ±5 ℃)
Tachometer (Output modes)
Upper and lower limit/ area/ upper limit/ lower limit
Tachometer (Auto-zero time)
0.1 to 99.9 s
Tachometer (Startup time)
0.0 to 99.9 s
Tachometer (Average processing)
OFF/ 2 times/ 4 times/ 8 times
Input signal
CP1 / CP2 / Reset1 / Reset2 / Key protect
Input method
No-voltage/Voltage input (selectable)
No-voltage input (No-contact input）
Short-circuit (ON) impedance: 1 kΩ
Leakage current (0 Ω): 12 mA
Residual voltage: 3 V max.
Open circuit impedance: 100 kΩ
Maximum voltage: 30 V
No-voltage input (Contact input）
Use a contact which can adequately switch 5 mA at 10 V.
Voltage input
Hight level: 4.5 to 30 VDC
Low level: 0 to 2 VDC
Input resistance: 4.7 kΩ
Applicable two-wire sensor
leakage current: 1.5 mA
Switching capacity: 5 mA
Residual voltage: 3 V
Operating voltage: 10 VDC
Minimum input signal width
External reset: 1 ms/20 ms (selectable)
Standby time
290 ms
Control output (Contact output)
2 stages of SPST-NO
Switching capacity: 3 A at 250 VAC/30 VDC, resistive load (cos phi=1)
Minimum applicable load: 10 mA at 5 VDC (failure level:P reference value)
Control output (Solid-state output)
Output type: Transistor output
Switching capacity: 30 VDC max., 100 mA max.
Residual voltage: 1.5 V max. (Actual performance 1.0 V)
Leakage current: 0.1 mA
Display method
7-segment backlit negative transmissive LCD
Digits
6digits
Character height
Count value: 13.5 mm (Red or green programmable)
Set value: 9 mm (Green)
Prescaling function
Provided (0.001 to 99.999)
Decimal point adjustment
Rightmost 3 digits
Key protection
Key protect input
Teaching function
Not provided
Batch counting function
Provided
Communications
Not provided
Memory backup
EEP-ROM (Number of rewite: 100,000 operations min.Service life: 10 years min.)
Surrounding air temperature
Operating: -10 to 55 ℃
Storage: -25 to 65 ℃
Ambient humidity
Operating: 25 to 85%
Storage: 25 to 85%
Insulation resistance
100 MΩ min. (at 500 VDC)
Between current carrying terminals and exposed non-current carrying metal parts / Between non-continuous contacts / Between operating circuit and control output and between contacts of different polarity
Dielectric withstand voltage
Between current carrying terminals and exposed non-current carrying metal parts:2000 VAC 50/60 Hz for 1 min
Between operating circuit and control output and between contacts of different polarity:2000 VAC 50/60 Hz for 1 min
Between non-continuous contacts:1000 VAC 50/60 Hz for 1 min
Impulse withstand voltage
Between power terminals:3.0 kV
Between current carrying terminals and exposed non-current carrying metal parts:4.5 kV
Noise immunity
Between power terminals:±1.5 kV
Between input terminals:±600 V
Square-wave noise by noise simulator (Pulse width: 100 ns/1 µs, 1-ns rise)
Static immunity
Mulfunction: 8 kV, Destruction: 15 kV
Vibration resistance （Destruction）
10 to 55 Hz, 0.75-mm single amplitude each in 3 directions for 2 h
Vibration resistance （Malfunction）
10 to 55 Hz, 0.5-mm single amplitude each in 3 directions for 10 min
Shock resistance （Destruction）
294 m/s**2, 3 times each in 6 directions (3 axes)
Shock resistance （Malfunction）
98 m/s**2, 3 times each in 6 directions (3 axes)
Mechanical life expectancy
10,000,000 operations min.
Degree of protection
Case front: IP54
Case rear: IP20
Terminal block: IP20
Mounting method
Flush mounting
External connection method
Screw terminal
Case color
Black (Munsell N1.5)
Accessories
Mounting bracket / Terminal cover / Labels for counter/tachometer DIP switch settings
Weight
Approx. 250 g
| Function | 1 Stage Preset Counter / 2 Stage Preset Counter / Total Preset Counter / Batch Counter / Dual Counter / Tachometer |
|---|---|
| Preset stages | 2stages |
| Rated supply voltage | 100 to 240 VAC 50/60 Hz |
| Operating voltage range | 85% to 110% of the rated power supply voltage |
| Power consumption | Approx. 9.6 VA |
| External power supply | 12 VDC (±10%) 100 mA |
| Counter (Count range) | -99999～999999 |
| Counter (Max. counting speed) | 30 Hz/5 kHz (switching) (Minimum counting input signal width: 16.7 ms (ON/OFF ratio: 1:1)/0.1 ms (ON/OFF ratio: 1:1)) Common setting for CP1 and CP2 |
| Counter (Input mode) | Increment decrement or increment/decrement (UP/DOWN A (command input), UP/DOWN B (individual input) and UP/DOWN C(quadrature input)) |
| Counter (Output modes) | N / F / C / R / K-1 / P / Q / A / K-2 / D / L / H |
| Counter One-shot time) | 0.01 to 99.99 s variable |
| Counter (Reset system) | External, manual and automatic reset (internal according to C, R, P and Q mode operation) |
| Tachometer (Pulse measurement method) | Periodic measurement |
| Tachometer (Sampling period) | Periodic measurement: 200 ms |
| Tachometer (Max. counting speed) | Periodic measurement: 30 Hz/10 kHz (selectable) |
| Tachometer (Count range) | 0 to 999999 |
| Tachometer (Measuring ranges) | Periodic measurement: 30 Hz: 0.01 Hz to 30.00 Hz Periodic measurement: 10 kHz: 0.01 Hz to 10 kHz |
| Tachometer (Measuring accuracy) | ±0.1% F.S. ±1 digit max. (at 23 ±5 ℃) |
| Tachometer (Output modes) | Upper and lower limit/ area/ upper limit/ lower limit |
| Tachometer (Auto-zero time) | 0.1 to 99.9 s |
| Tachometer (Startup time) | 0.0 to 99.9 s |
| Tachometer (Average processing) | OFF/ 2 times/ 4 times/ 8 times |
| Input signal | CP1 / CP2 / Reset1 / Reset2 / Key protect |
| Input method | No-voltage/Voltage input (selectable) |
| No-voltage input (No-contact input） | Short-circuit (ON) impedance: 1 kΩ Leakage current (0 Ω): 12 mA Residual voltage: 3 V max. Open circuit impedance: 100 kΩ Maximum voltage: 30 V |
| No-voltage input (Contact input） | Use a contact which can adequately switch 5 mA at 10 V. |
| Voltage input | Hight level: 4.5 to 30 VDC Low level: 0 to 2 VDC Input resistance: 4.7 kΩ |
| Applicable two-wire sensor | leakage current: 1.5 mA Switching capacity: 5 mA Residual voltage: 3 V Operating voltage: 10 VDC |
| Minimum input signal width | External reset: 1 ms/20 ms (selectable) |
| Standby time | 290 ms |
| Control output (Contact output) | 2 stages of SPST-NO Switching capacity: 3 A at 250 VAC/30 VDC, resistive load (cos phi=1) Minimum applicable load: 10 mA at 5 VDC (failure level:P reference value) |
| Control output (Solid-state output) | Output type: Transistor output Switching capacity: 30 VDC max., 100 mA max. Residual voltage: 1.5 V max. (Actual performance 1.0 V) Leakage current: 0.1 mA |
| Display method | 7-segment backlit negative transmissive LCD |
| Digits | 6digits |
| Character height | Count value: 13.5 mm (Red or green programmable) Set value: 9 mm (Green) |
| Prescaling function | Provided (0.001 to 99.999) |
| Decimal point adjustment | Rightmost 3 digits |
| Key protection | Key protect input |
| Teaching function | Not provided |
| Batch counting function | Provided |
| Communications | Not provided |
| Memory backup | EEP-ROM (Number of rewite: 100,000 operations min.Service life: 10 years min.) |
| Surrounding air temperature | Operating: -10 to 55 ℃ Storage: -25 to 65 ℃ |
| Ambient humidity | Operating: 25 to 85% Storage: 25 to 85% |
| Insulation resistance | 100 MΩ min. (at 500 VDC) Between current carrying terminals and exposed non-current carrying metal parts / Between non-continuous contacts / Between operating circuit and control output and between contacts of different polarity |
| Dielectric withstand voltage | Between current carrying terminals and exposed non-current carrying metal parts:2000 VAC 50/60 Hz for 1 min Between operating circuit and control output and between contacts of different polarity:2000 VAC 50/60 Hz for 1 min Between non-continuous contacts:1000 VAC 50/60 Hz for 1 min |
| Impulse withstand voltage | Between power terminals:3.0 kV Between current carrying terminals and exposed non-current carrying metal parts:4.5 kV |
| Noise immunity | Between power terminals:±1.5 kV Between input terminals:±600 V Square-wave noise by noise simulator (Pulse width: 100 ns/1 µs, 1-ns rise) |
| Static immunity | Mulfunction: 8 kV, Destruction: 15 kV |
| Vibration resistance （Destruction） | 10 to 55 Hz, 0.75-mm single amplitude each in 3 directions for 2 h |
| Vibration resistance （Malfunction） | 10 to 55 Hz, 0.5-mm single amplitude each in 3 directions for 10 min |
| Shock resistance （Destruction） | 294 m/s**2, 3 times each in 6 directions (3 axes) |
| Shock resistance （Malfunction） | 98 m/s**2, 3 times each in 6 directions (3 axes) |
| Mechanical life expectancy | 10,000,000 operations min. |
| Degree of protection | Case front: IP54 Case rear: IP20 Terminal block: IP20 |
| Mounting method | Flush mounting |
| External connection method | Screw terminal |
| Case color | Black (Munsell N1.5) |
| Accessories | Mounting bracket / Terminal cover / Labels for counter/tachometer DIP switch settings |
| Weight | Approx. 250 g |